Entrée Phono du Conrad Johnson PV9A
Le passé aurait de l'avenir.
Entrée Phono du Conrad Johnson PV9A
#1 par olivier-49 » 15 Juil 2021 à 19:11
Hello guys !
Dites-moi, l'entrée phono du PV9A est adaptée aux cellules MM et aux MC à haut niveau de sortie, OK ? Voir manuel CJ :
"Phono input:This input provides the amplification and equalization required by moving magnet and high output moving coil cartridges. The input impedance is the industry standard 47,000 ohms shunted by approximately 100 picofarads apacitance. This is well suited to nearly all moving magnet and many high- output moving coil cartridges. If necessary, the input impedance can be lowered by soldering a resistor across ( from center pin to ground) the input jack. To achieve a desired
input resistance of RD, use the following formula to compute the required additional resistance RA:
RA = 47000*RD/(47000-RD)
Some moving magnet cartridges require higher capacitance for optimum performance. Increasing the input capacitance may be achieved by soldering a suitable value capacitor across the phono input jack. Use polystyrene capacitors for this purpose
Mais qu'est-ce que ça veut dire MC à haut niveau de sortie please ? Merci.
Dites-moi, l'entrée phono du PV9A est adaptée aux cellules MM et aux MC à haut niveau de sortie, OK ? Voir manuel CJ :
"Phono input:This input provides the amplification and equalization required by moving magnet and high output moving coil cartridges. The input impedance is the industry standard 47,000 ohms shunted by approximately 100 picofarads apacitance. This is well suited to nearly all moving magnet and many high- output moving coil cartridges. If necessary, the input impedance can be lowered by soldering a resistor across ( from center pin to ground) the input jack. To achieve a desired
input resistance of RD, use the following formula to compute the required additional resistance RA:
RA = 47000*RD/(47000-RD)
Some moving magnet cartridges require higher capacitance for optimum performance. Increasing the input capacitance may be achieved by soldering a suitable value capacitor across the phono input jack. Use polystyrene capacitors for this purpose
Mais qu'est-ce que ça veut dire MC à haut niveau de sortie please ? Merci.
-
olivier-49 - 100 watts
- Messages: 1440
- Inscription: 10 Nov 2010 à 09:46
- Localisation: Angers
Re: Entrée Phono du Conrad Johnson PV9A
#2 par Time Window » 15 Juil 2021 à 19:34
Hello Olivier
MC haut niveau = technologie MC avec un niveau de sortie de l'ordre de 2 à 3 mV,
alors qu'une MC bas c'est niveau c'est entre 0,2 et 0,5 mV
Ce "Haut niveau dispense de l'utilation d'un transfo ou Prepre.
Plusieurs fabricants en ont à leur catalogue.
Dynavector, Hana, Sumiko, et bien d'autres.
.
MC haut niveau = technologie MC avec un niveau de sortie de l'ordre de 2 à 3 mV,
alors qu'une MC bas c'est niveau c'est entre 0,2 et 0,5 mV
Ce "Haut niveau dispense de l'utilation d'un transfo ou Prepre.
Plusieurs fabricants en ont à leur catalogue.
Dynavector, Hana, Sumiko, et bien d'autres.
.
-
Time Window - 100 watts
- Messages: 2276
- Inscription: 12 Fév 2017 à 15:18
- Localisation: Sarthe
Re: Entrée Phono du Conrad Johnson PV9A
#3 par olivier-49 » 15 Juil 2021 à 22:31
OK, merci, tu as parfaitement répondu à ma question !
J'ai l'occasion d'essayer une Audio Technica AT 33 de 0,5 mV (tension de sortie). Il me faudra donc le pré-pré.
J'ai l'occasion d'essayer une Audio Technica AT 33 de 0,5 mV (tension de sortie). Il me faudra donc le pré-pré.
-
olivier-49 - 100 watts
- Messages: 1440
- Inscription: 10 Nov 2010 à 09:46
- Localisation: Angers
Qui est en ligne
Utilisateurs parcourant ce forum: Aucun utilisateur enregistré et 21 invités
Développé par phpBB® Forum Software © phpBB Group