conrad johnson mv75
Les "vieilleries" électroniques.
Retourner vers Amplis, Tuners, Cd...
conrad johnson mv75
#1 par leedh » 20 Nov 2010 à 17:37
Bonjour à tous!
je viens d'acheter un conrad Johnson MV75 à bon prix. il est en bon état mais son precedent propriétaire a égaré la face avant et le capot (d'où le bon prix....). il est donc tout nu!
je dois lui coller des 6550 car il est non tubé. oui mais voilà, il faut régler le bias et je ne sais pas du tout comment faire!
alors si une ame charitable fan de Conrad pouvait me filer un coup de main....
merci!
Olivier
je viens d'acheter un conrad Johnson MV75 à bon prix. il est en bon état mais son precedent propriétaire a égaré la face avant et le capot (d'où le bon prix....). il est donc tout nu!
je dois lui coller des 6550 car il est non tubé. oui mais voilà, il faut régler le bias et je ne sais pas du tout comment faire!
alors si une ame charitable fan de Conrad pouvait me filer un coup de main....
merci!
Olivier
-
leedh - 50 watts
- Messages: 559
- Inscription: 25 Oct 2010 à 20:38
Re: conrad johnson mv75
#2 par leedh » 20 Nov 2010 à 17:47
Ca y est, j'ai trouvé! je n'avais pas pensé à aller voir sur le site CJ.
voilà ce qu'il dise :
Q. How do I bias my power output tubes?
A. Conrad-Johnson tube amplifiers feature a unique, easy to use bias circuit. Biasing is done with NO signal going to the amplifier (turn the preamp off, or all the way down). Let the amplifier warm up for about half an hour (if biasing a new set of tubes for the first time, do this first after about 3-4 minutes, then repeat once after a half an hour). Adjacent to each output tube you will see an adjustment screw and an indicator light. After the amplifier has warmed up, turn the screw clockwise until the red light comes on. Then slowly back off (counter-clockwise) that adjustment until the red LED just goes off and stays off. You will need to do this for each tube. Some of the LED’s may come back on while you are adjusting other tubes. Just re-adjust so that all of the LED’s are off after all adjustments are completed.
After the biasing procedure is completed, you may find the indicator lights coming on from time to time when no music is playing. This can happen as power line voltages vary over time, and as the amplifier conditions change a bit with use. There is no need to re-bias unless all leds come on and stay on for several minutes.
on ne peut plus simple!
voilà ce qu'il dise :
Q. How do I bias my power output tubes?
A. Conrad-Johnson tube amplifiers feature a unique, easy to use bias circuit. Biasing is done with NO signal going to the amplifier (turn the preamp off, or all the way down). Let the amplifier warm up for about half an hour (if biasing a new set of tubes for the first time, do this first after about 3-4 minutes, then repeat once after a half an hour). Adjacent to each output tube you will see an adjustment screw and an indicator light. After the amplifier has warmed up, turn the screw clockwise until the red light comes on. Then slowly back off (counter-clockwise) that adjustment until the red LED just goes off and stays off. You will need to do this for each tube. Some of the LED’s may come back on while you are adjusting other tubes. Just re-adjust so that all of the LED’s are off after all adjustments are completed.
After the biasing procedure is completed, you may find the indicator lights coming on from time to time when no music is playing. This can happen as power line voltages vary over time, and as the amplifier conditions change a bit with use. There is no need to re-bias unless all leds come on and stay on for several minutes.
on ne peut plus simple!
-
leedh - 50 watts
- Messages: 559
- Inscription: 25 Oct 2010 à 20:38
Re: conrad johnson mv75
#3 par steph2401 » 20 Nov 2010 à 17:50
J'espère pour toi que tu l'as eu à un TRÈS bon prix.
Pour le bias tu allumes l'ampli et tu mets ton préamp à zéro en sélectionnant une source non utilisée.
Au bout d'une minute tu tournes les petites vis au fond des trous à côtés de tubes jusqu'à éteindre les LED rouges.
Tu fais deux fois le tour des 4 tubes en te mettant toujours juste après l'extinction.
Au bout de 30mn de chauffe tu refais la même opération.
Si tes tubes sont bons tu es tranquille pour plusieurs mois.
Que les LED clignotent pendant la musique c'est normal.
Stéphane
Pour le bias tu allumes l'ampli et tu mets ton préamp à zéro en sélectionnant une source non utilisée.
Au bout d'une minute tu tournes les petites vis au fond des trous à côtés de tubes jusqu'à éteindre les LED rouges.
Tu fais deux fois le tour des 4 tubes en te mettant toujours juste après l'extinction.
Au bout de 30mn de chauffe tu refais la même opération.
Si tes tubes sont bons tu es tranquille pour plusieurs mois.
Que les LED clignotent pendant la musique c'est normal.
Stéphane
-
steph2401 - 100 watts
- Messages: 2763
- Inscription: 30 Juin 2010 à 14:08
- Localisation: Région Bordelaise
Retourner vers Amplis, Tuners, Cd...
Qui est en ligne
Utilisateurs parcourant ce forum: oliv44 et 13 invités
Développé par phpBB® Forum Software © phpBB Group